Brand New Module Fuji NP1F-MM1 In Stock
Description
Your Fuji Spraygun has been adjusted at the factory and is ready for spraying. To clean out any impurities that may have accumulated during assembly or shipping, we recommend spraying a small quantity of clean paint thinner through the gun. Before tackling any serious spraying, experiment with the gun on a scrap piece of wood or cardboard until you become familiar with all the controls.
Turn the air nozzle until it clicks into the horizontal position. This setting produces a vertical pattern useful for spraying from side to side. Set the nozzle in a vertical position. This setting produces a horizontal pattern, useful for spraying up and down. Now try setting the nozzle at a 45º angle. This setting produces a round pattern useful for spraying thinner objects. Remember to turn down the amount of paint when you switch to a smaller round pattern, otherwise you will find that there will be too much paint concentrated in one spot. To test, try turning the fluid adjusting screw (part. 2019) clockwise until you cannot pull the trigger. Then unscrew it a little until a small amount of paint material comes out of the jet when you depress the trigger. This results in a small circular pattern. If you continue to depress the trigger and move along your workpiece you will get a fine line. From 6” away this will give you a pattern about 1” - 2” in diameter.
This would be handy for spraying thin spindles in a chair for instance. Then place the nozzle to where it almost touches the test board and the pattern becomes extremely small - similar to an airbrush. Try writing your name with the gun. If you get runs then you will have to adjust the fluid adjusting screw again at the back of the gun. This type of technique is handy for repairs and touch-up. To obtain more coverage with a fuller spray, unscrew the fluid adjusting screw. Experimenting like this enables you to become familiar with your Fuji spraygun.
More Products
| NV1F-HC1 | NP1W6406U | NP1AXH8IG-MR |
| NP1Y64U09P1 | NP1AXH8VG-MR | NC1Y16R-08 |
| FPU140S-A10 | NC1F-PY1 | NP1X0805 |
| NV1P-082 | NP1L-LL2 | CTHMIMOD-00 |
| FEH323 | NR1LW-11R80DT | NC1AX02-PT |
| FGU120B | NP1BP-13D | NP1Y32T09P1 |
| NU2V-PA1 | RYS501S3-VVS-Z71 | NP1AXH6G-PT |
| NP1L-AS2 | NP1S-81 | NP1L-JS1 |
| NP1PU2-256E | NV1Y16T05P5 | FPU150S-A10 |
| NP1PM-48E | NB1W56R-11 | FEH241 |
| NP1L-OL2 | FTU155C | NJ-Y16-TF2C8 |
| NP1BP-13 | NP1AXH8V-MR | NP1L-RD1 |
You May Like
| Hima | Epro | ProSoft |
| CPU01 | PR6423/00R-101 CON031 | MVI71-ADM |
| B5322 | A6110 | PS69-DPS |
| BV7032-0 | A6120 | PS69-DPM |
| BV7040-4 | A6210 | PC56-2K-IDE |
| BV7046-4 | A6220 | MVI94-MCM |
| F1101 | A6312 | MVI71-AFC |
| F1DI1601 | A6410 | MVI69-PDPS |
| F2201 | CON021 PR6423/002-000 9200-00006N | MVI69-PDPMV1 |
| F2DO1602 | CON041 PR6423/002-011 9200-00021N | MVI69-MNET |
| F2DO8 01 | MMS3120/022-100 | MVI69-MCM |
| F3113A | MMS6110 | MVI69L-MBS |
| F3221 | MMS6120 | MVI69-GSC |
Hello, Do You Interested In PLC,DCS?
We are the supplier for industrial automation spare parts.
We specialize in PLC module, DCS card pieces, ESD system card pieces, vibration monitoring system card pieces, steam turbine control system module, gas generator spare parts.
We have large of inventory for our company's advantage products: YOKOGAWA , AB, ABB, GE, BENTLY NEVADA, EMERSON, HONEYWELL, FOXBORO, TRICONEX. etc.
Grateful for your valuable time. If you have any requirements, please send me an inquiry.
