Fuji NP1AXH4-TC100% New And Original Module In Box
Description
Like other spraygun manufacturers, we use ‘stock’ stainless steel rod for the needle. This rod can differ in diameter slightly with each run. This means that when you change say, a #3 for a #4 needle. One could be slightly oversized diameter and one slightly undersized. This neccessitates adjusting the needle seal. The needle seal bushing (packing) must be tight enough to prevent any leakage of paint material into the gun. It should however, allow the needle to glide smoothly through it. If this bushing is too loose often a ‘pulsating’ of the spray pattern will be seen.
Insert the needle seal adjusting tool (with teeth pointing downwards) over the needle. This is the tubular-shaped tool that comes with the complete Fuji system. Locate the slots in the needle seal nut and tighten the needle seal while continually pulling the trigger. (If the slots are clogged with paint, use a sharp screwdriver to clean out the slots). Once the needle is grabbed by the seal, back off the screw a very slight amount. The needle seal is adjusted perfectly just short of the point where the needle sticks. Another guide is to grasp the end of the needle and shake it firmly but gently from side to side - there should be no play - but the needle should still slide smoothly without sticking when the trigger is pulled. The needle seal should never need replacing.
Fuji Products
| NC1X3204 | NP1PU-128EZM | FTU123B |
| FTU110B | FTU500A | NR1DY-16T05DT |
| NP1L-JP1 | NJ-HC | NC1F-VP1 |
| NP1L-PE1 | NP4N-ITGR | NP4N-IPAC |
| NP1L-UC1 | FTU113B | FTK500A-C10 |
| NR1JX-1606DT | CHBAPWM05-102 | NP1PM-48R |
| FTU211B | NR1DW-16T65DT | NP1AYH8V-MR |
| NP1S-91/81 | NC1H-TL1 | NV1X1604-W |
| NP1S-22 | NC1Y32T05P1 | NR1DY-08R07DT |
| NP4H-SEDBV3 | NV1L-TL1 | NP1Y08U0902 |
| NP1AWH6-MR | NP1L-RP1 | NP1Y64T09P1 |
| NP3PS-SX1PCS74 | Y16-SF1 | NP1PS-16 |
| NP1BS-06 | NR1LY-08R07DT | NP3L-FL3PCS |
You May Like
| Siemens | Triconex | Schneider |
| 16267-1/4 | Triconex 4000042-120 | UST21 |
| 146659-069 | Triconex 219179 | 140ACI03000 |
| 15377-4FM | Triconex 2201 CM 2201 | 140ACI04000 |
| 15738-119 | Triconex 2351 | 140ACI05100 |
| 16135-21-2 | Triconex 2352 | 140ACO02000 |
| 16147-51-2 | Triconex 2361 | 140ACO13000 |
| 16168-1-1 | Triconex 2381 | 140AII33010 |
| 16180-500 PSMBXNAN | Triconex 2401 | 140AMM0900 |
| 16182-1-3 | Triconex 2401L | 140ARI03010 |
| 16187-1-1 | Triconex 2451 | 140AVI03000 |
| 16249-51-4 | Triconex 2481 | 140AVO02000 |
| 16267-1-2 | Triconex 2551 | 140CHS11000 |
Advantage Products
1.Allen-Bradley 1756/1769/1771/1785 Series
2.ABB 800xA/Bailey INFI90/DSQC Series
3.Bently Nevada 3500/3300 Monitoring System
4.Schneider Series Quantum 140 series
5.General Electric IC693/IC697/IC698/IS200/DS200 Series
6.SIEMENS MOORE/S5 Series
7.Westinghouse: OVATION/WDPF/MAX1000 system spare parts
8.Invensys Triconex: Redundant fault-tolerant control system, Most modern fault-tolerant controller based on Triple Modular Redundancy (TMR) architecture
9.Honeywell TDC2000/TDC3000/Experion HS Series
10.YOKOGAWA CS3000 System
